PDA

View Full Version : BE aftermarket rear endlink options - as of 12/09?



Markus
12-20-2009, 11:28 AM
Hello everyone -

I have a 2003 Legacy GT sedan with aftermarket 22mm IPD rear sway bar. Like alot of others before me, I'm getting some moderate clunking between the sway bar and the lower control arms.

Current plan of attack:
1) Push sway bar mount brackets up as high as possible (already appear to be centered so won't gain much clearance).
2) Zip tie some rubber tubing around swaybar at contact point.
3) Turn up radio and try to ignore.

I know the above steps aren't going to totally solve the problem though. What will solve the problem is some slightly longer rear end links. Yes I've searched, but most of what I see referenced in the past is no longer available. Does anyone have any good current ideas or sources?
1) Miata end links - Rougeben used some of these in the past, he got them cheap and they required some modification. I can no longer find a cheap source - most Spec Miata websites carry adjustable rear end links but cost is like $100 and they'd still require modification.
2) Aftermarket for Subie - As I'm sure you guys know it's really hard to find aftermarket parts listed for the 2000-2004 Leggy's any more. Is there a Whiteline or Rallitek product for an Impreza or other chassis that will work? I'm not real hot on spending $100+ for something aftermarket, but if it was direct fit and didn't require modification - might be worth it?
3) Aftermarket for ?? - I saw reference to some cheap Corvette/GM end links that might work, any info on these? Any idea what measurement range I'd need? (IE - must be adjustable from 3-3.5"?).

Thanks if anyone can point me in the right direction. I really do want to fix it right. And I really dislike the stock end links so changing won't break my heart, I'm just ticked I'll have to mess with them again at all (and the fact that it's another cold winter here in Ohio).

- Mark

Airgne
12-20-2009, 02:10 PM
http://www2.kartboy.com/x4/product.php? ... stseller=Y (http://www2.kartboy.com/x4/product.php?productid=16143&cat=263&bestseller=Y)
http://www2.kartboy.com/x4/product.php? ... 253&page=3 (http://www2.kartboy.com/x4/product.php?productid=16192&cat=253&page=3)
http://www.groupa.ca/PR_end_links.html

the above links are for endlinks that will work on our cars. if you dont want to spend over 100 bucks than you will not get anything good.

rougeben83
12-20-2009, 03:25 PM
those aren't adjustable, you need about another 1inch longer endlinks to move the swaybar away from the lower control arm. The only one that I know are adjustable are the whitelines.

IIRC, you need 4.5" long eye to eye; the stock ones are less than 3.5" eye to eye.

You can make some of your own by ordering from http://www.mcmaster.com/ and buying the eyes and right length rods.

Heim joints get loose over time, the miata endlinks ended up replacing in about 2 years (no real noise, just that if you move the swaybar you can see a little play in the endlink joint), I have whiteline ones now who knows how long they'll last.

Markus
12-21-2009, 11:51 AM
Ben -

Thanks for the length info! I'll look around, see if I can find something non-adjustable.

If I can't, any info on the Whitelines you got - part #, source, etc?

- Mark

Markus
12-21-2009, 11:57 AM
Heim joints get loose over time, the miata endlinks ended up replacing in about 2 years (no real noise, just that if you move the swaybar you can see a little play in the endlink joint), I have whiteline ones now who knows how long they'll last.

Just a ghetto thought, set to right adjustment height - then weld in place? No getting loose then! :twisted:

Huffer
12-21-2009, 01:05 PM
There was a fella awhile back ( I think DVS motorsports or something in Chicago? I have the name wrong I'm sure!) that made up his own rear adjustable control arms and endlinks... There is a thread about it in here somewhere...

rougeben83
12-21-2009, 04:17 PM
Ben -

Thanks for the length info! I'll look around, see if I can find something non-adjustable.

If I can't, any info on the Whitelines you got - part #, source, etc?

- Mark

http://www.whiteline.com.au/product_det ... ber=KLC044 (http://www.whiteline.com.au/product_detail.php?part_number=KLC044)

Markus
12-23-2009, 09:38 AM
Ben thanks for the info!

I have one more stooopid question: Does the length of endlink I need change if I lower the car in the future?

Right now the car is on stock struts/springs. I have some lowering springs in my basement that I'd like to install with Bilsteins at some point. Not sure if that will change the angles/dynamics at all?

Thanks.....

- Mark

Huffer
12-23-2009, 10:30 AM
There was a fella awhile back ( I think DVS motorsports or something in Chicago? I have the name wrong I'm sure!) that made up his own rear adjustable control arms and endlinks... There is a thread about it in here somewhere...

I'm a noob. DS1...

viewtopic.php?f=13&t=12007 (https://sl-i.net/FORUM/viewtopic.php?f=13&t=12007)