Zac's BP5, SpecB Wannabe, Rallycross Time.

[Zac]

https://sl-i.net/FORUM/images/imported/2010/07/20110520205849_Morinville_Alberta_CA-1.jpg]

MODS:

Engine:
-GroupA Pitch Stopper Mount
-COBB SF Intake
-STi Genome Axleback Mufflers
-COBB Accessport Stage 1 Tune
-TGV Deletes
-AVO Turbo Inlet


Suspension:
-JDM SpecB Rev.A Bilsteins and Springs

Brakes:
-Stoptech brake Pads
-Stoptech Cryo Rotors
-GrimmSpeed Master Cylinder Brace
-ATE Super Blue Brake Fluid
-Techna-Fit Steel braided brake lines

Wheels:
-Winter / Dunlop Graspic DS-2 215/50/R17 On Stock rims Painted Pink
-06 SpecB wheels with BFG G-Force Sport Comp2's 215/45/ZR18

Exterior:
-Debadge
-Tint
-JDM GT Grille
-Slight Tint Amber Portion of Tail Lights
-Nokya Yellow Fog light bulbs

Interior:
-Prodrive Shift Knob

Drivetrain:
-Spec Dual Mass LW Flywheel
-Spec Stage2+ Clutch
-Group N Transmission Mount
-Group N Transmission Crossmember Bushings
-Group N Rear Shifter Stay Bushing
-Kartboy Shifter Bushings
-Subaru Extra-S Gear Oil






Hey guys! Some of you may rememeber me with a 1998 legacy wagon (Thread here: viewtopic.php?t=14946 (https://sl-i.net/FORUM/viewtopic.php?t=14946) ) but it was giving me too many problems and needed a reliable car so I bit the bullet and got a 2005 Legacy GT Wagon!!

[chuckthefuk]

sweeeet

[httrdd]

Very nice upgrade!

[Zac]

Thanks guys! Just ordered some Stoptech brake pads, Gaskets to fix my leaking cross pipe and yellow headlight and foglight bulbs! I cant wait to install :D

[richysteele]

OMg we did the same thing! I totaled my 98 an bought an 05 sedan! Ironic! (you couldnt crop out the honda lolz j/k)

[lord flashheart]

i did something much similar. sold the 99 OB and got a 06 OBXT. its weird getting used to all the power.

[parkcityboyx]

dude when you said you got a new leggy i figured you got another 95-99 GT or something! hahaha, this is awesome! im stoked for you man. when i get a little bit more money in my pocket im doing the same thing or going WRX not sure yet.

good shit!!

[deadlydave]

Niceeee ride. I was looking for a used 5mt lgt wagon a while ago, but I founds something a lot better for a lot cheaper.

I like the blue, gold or bronze wheels set off the paint nicely.

[parkcityboyx]

lookin for that pm reply :))))))) hope all is well with that pretty new ride you got. jealouss!!

girlfriends hot!

kudos


o nice car too i guess, lol

[Zac]

Hey guys sorry for being away for a long time! Moved 30 hours away from my hometown to a new province, and they dont require front plates here!

Little Photo shoot after detailing my wagon!

https://sl-i.net/FORUM/images/imported/2010/09/DSC00339-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00340-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00342-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00343-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00344-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00345-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00346-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00347-1.jpg

[ESSYMOND]

What a beautiful exhaust,

how much did that cost you lol

[Zac]

not much, think I only payed $480 shipped

Only Axle back though

[Zac]

Headlights were looking a bit hazy and decided to try and buff them out.

https://sl-i.net/FORUM/images/imported/2010/09/DSC00383-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00384-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00385-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00386-1.jpg

My Weapons of Choice:

https://sl-i.net/FORUM/images/imported/2010/09/DSC00387-1.jpg

Driver's Side done:

https://sl-i.net/FORUM/images/imported/2010/09/DSC00389-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00390-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00391-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00392-1.jpg

Passenger Side done:

https://sl-i.net/FORUM/images/imported/2010/09/DSC00393-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00394-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00395-1.jpg

Both sides finished:

https://sl-i.net/FORUM/images/imported/2010/09/DSC00396-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00398-1.jpg
https://sl-i.net/FORUM/images/imported/2010/09/DSC00399-1.jpg

[MrChefNz]

Where did you get exhaust tips from? They look sick dude.

[Zac]

STi Genome Mufflers

Won them off of ebay :)

[Matt S.]

Love the wagons!!!

And yes, that exhaust is total win.

Just be sure to(if you didn't already) read up about the dreaded turbo banjo bolt screen and the oil pick up tube while you're at it.

[Zac]

Long story short, got rear ended december 3rd getting repaired now :)

http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1338.snc4/163017_10150131608418976_511108975_7876668_3193947_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1120.snc4/148229_10150131608528976_511108975_7876674_3086461_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs739.snc4/63942_10150131608623976_511108975_7876676_841294_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1337.snc4/162942_10150131608753976_511108975_7876681_1738442_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs400.ash2/67834_10150131608818976_511108975_7876684_5147146_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs694.snc4/63477_10150140558843976_511108975_8013305_4083102_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1385.snc4/163751_10150140558903976_511108975_8013306_7931840_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash1/hs753.ash1/164473_10150140559008976_511108975_8013309_1379036_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs213.ash2/47649_10150140559058976_511108975_8013310_2025256_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs933.snc4/74658_10150140559228976_511108975_8013314_1680126_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash1/hs736.ash1/162947_10150140559308976_511108975_8013317_5761535_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash1/hs749.ash1/164057_10150140559413976_511108975_8013318_4999897_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs213.ash2/47664_10150140559453976_511108975_8013319_1884547_n.jpg
http://l30.sphotos.l3.fbcdn.net/hphotos-l3-ash2/hs045.ash2/35628_10150140559528976_511108975_8013321_1425694_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1354.snc4/162627_10150140559608976_511108975_8013323_1976862_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs380.ash2/65813_10150140559678976_511108975_8013324_8094913_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1218.snc4/157009_10150140559743976_511108975_8013327_4677455_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1211.snc4/156384_10150140559818976_511108975_8013330_7085091_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc6/hs013.snc6/166350_10150140559893976_511108975_8013331_6064556_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash1/hs774.ash1/166494_10150140559933976_511108975_8013332_5438517_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs738.snc4/65817_10150140559973976_511108975_8013333_4228417_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1236.snc4/156808_10150143740268976_511108975_8072551_7139617_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs473.ash2/74650_10150143740448976_511108975_8072559_360884_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1382.snc4/163478_10150143740578976_511108975_8072566_1905928_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs887.snc4/72013_10150143740713976_511108975_8072573_4537550_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs618.ash2/157095_10150143740813976_511108975_8072578_5924328_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1338.snc4/163047_10150143740943976_511108975_8072584_563553_n.jpg

[chuckthefuk]

:-(

[-J.M.G.-]

:smt013 :smt013 :smt013 !!

[lord flashheart]

Oh shit... thats a bummer. It seems like it only happens to cars you love.. had my truck 3 years.. never been hit or anything. Had my outback XT for two weeks before some one backed into it and a month after that I got rear ended... idiot drivers..

[Zac]

well it looks alot worse then what it is, there is absolutly nothing wrong with the car, the subframe or suspensions were not hit, even the floor was fine :)

So my whole front end is getting repainted so all the rock chips will be gone :D :D

Also should be picking up some 17" Prodrive GC-05A's next week!!

[BE-Fresh]

Compared to that Acura, I think you came out of it pretty well!

[MudRunner]

That's a reasonably epic upgrade if you ask me.

And I'm gonna be the guy to break the rules.... the chick. She has red hair. +1

[lord flashheart]

Compared to that Acura, I think you came out of it pretty well!
Yeah especially because his insurance Ian't going to go up like the acura guys will.

[Zac]

That's a reasonably epic upgrade if you ask me.

And I'm gonna be the guy to break the rules.... the chick. She has red hair. +1

Thanks, shes a handfull (like all readheads) But I love and hope to spend the rest of my life with her! Big words for a young guy like me!

[Zac]

[quote="BE-Fresh":1wm66zkm]Compared to that Acura, I think you came out of it pretty well!
Yeah especially because his insurance Ian't going to go up like the acura guys will.[/quote:1wm66zkm]

Yes, hes screwed just got his licence too not even a month!

[Zac]

few more pics!

http://sphotos.ak.fbcdn.net/hphotos-ak-snc6/hs018.snc6/166836_10150150798763976_511108975_8227078_5841978_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc6/hs050.snc6/168016_10150150798838976_511108975_8227079_5569660_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1376.snc4/164890_10150150799333976_511108975_8227081_7561637_n.jpg

[burningindulge]

That's a reasonably epic upgrade if you ask me.

And I'm gonna be the guy to break the rules.... the chick. She has red hair. +1

Thanks, shes a handfull (like all readheads) But I love and hope to spend the rest of my life with her! Big words for a young guy like me!



I agree, my redhead is quite the handful as well.

[Zac]

all masked, getting painted monday :)

http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1368.snc4/164050_10150154104358976_511108975_8285907_4752295_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc6/hs011.snc6/166187_10150154104473976_511108975_8285910_7002483_n.jpg

[chrish8r]

Man.......that exhaust looked like it was bent like hell......damn acuras.....

[Zac]

The mufflers are fine, one needs a little weld around the seem but it will be ok :)

[xoSubieLegacyxo]

It looked nice. Are you keeping the original color?

[Zac]

It looked nice. Are you keeping the original color?

yepperz

[Zac]

so just want to write down a few future goals I would like to get done this summer:

-Build my own Heatshield for my intake
-Drain all drivetrain fluids and replace with Subaru Extra-S fluid
-Fix my broken stock grille and paint it to replicate a JDM SpecB grille
-Stoptech Rotors upfront
-Figure out what damn light bulbs I want! I must have been through like 10 different sets and i'm not happy with anything yet!

[Zac]

Here are the painted pics, looks better then what it is, our shitty old paint booth's doors barely close so its full of dust particles everywhere but on the bright side i'm getting payed to sand and polish my own car ;D

http://sphotos.ak.fbcdn.net/hphotos-ak-snc6/hs072.snc6/168263_10150156317833976_511108975_8324102_3096044_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs009.snc4/33832_10150156317913976_511108975_8324103_2056847_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1334.snc4/162657_10150156317963976_511108975_8324104_4013842_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1373.snc4/164499_10150156318063976_511108975_8324105_1997138_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc6/hs067.snc6/167749_10150156318143976_511108975_8324106_2306380_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash1/hs737.ash1/163003_10150156318238976_511108975_8324108_1438142_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1382.snc4/163421_10150156318288976_511108975_8324109_7238319_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc6/hs066.snc6/167670_10150156318348976_511108975_8324110_4909817_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash1/hs783.ash1/167330_10150156318413976_511108975_8324111_4893451_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash1/hs781.ash1/167156_10150156318508976_511108975_8324112_7711866_n.jpg

Front end is a bit hazy cause I asked for a few extra coats of clear on it to help against rock chips, nothing my sanding and polishing skills cant handle to turn it into a glass finish :D

[Huffer]

Looks great! I should come see you for a paint job.

[LiCelsior]

i like that paint color!

[xoSubieLegacyxo]

Looks great! Reinstall the parts back on and get her out on the road!!! lol

[Zac]

tailgate needs to be repainted, full of pinholes in one area

[Zac]

She's back!

http://sphotos.ak.fbcdn.net/hphotos-ak-snc6/hs262.snc6/179076_10150163149793976_511108975_8429294_7898141_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc6/hs274.snc6/180244_10150163149888976_511108975_8429297_8124103_n.jpg

[Zac]

Bought some maintenance items today to welcome her back.

https://sl-i.net/FORUM/images/imported/2011/01/DSC00465-1.jpg

Dirty COBB Air filter!
https://sl-i.net/FORUM/images/imported/2011/01/DSC00469-1.jpg

Pretty bulbs!
https://sl-i.net/FORUM/images/imported/2011/01/DSC00471-1.jpg

And a new coat to match my car!
https://sl-i.net/FORUM/images/imported/2011/01/DSC00474-1.jpg

[xoSubieLegacyxo]

haha gotta look good while your driving the subie!! Glad you got her fixed.

[SOREN]

Lookin' sexy Zach, I'll probably "run into you" on the streets in the next couple weeks (we always seem to "bump" into each other!)

Great to be back on the road. I'm doing mine through cougar, booked in a week monday.

[Zac]

Lookin' sexy Zach, I'll probably "run into you" on the streets in the next couple weeks (we always seem to "bump" into each other!)

Great to be back on the road. I'm doing mine through cougar, booked in a week monday.

Thats Great man! We'll have to get together for coffee sometime when shes ready, I want to see it up close :)

[Zac]

haha gotta look good while your driving the subie!! Glad you got her fixed.

Thanks buddy! I like your legacy too!

[SOREN]

yeah, I'd be good with coffee sometime. I'll let you know, it'd have to be pretty quick after though, I've had a buyer that wanted my Legacy for the last month, and he's still wants it, but baaa-aad now.. even though it needs repair. So we'll have to do this in the first couple days I get this back I think.

[Zac]

yeah, I'd be good with coffee sometime. I'll let you know, it'd have to be pretty quick after though, I've had a buyer that wanted my Legacy for the last month, and he's still wants it, but baaa-aad now.. even though it needs repair. So we'll have to do this in the first couple days I get this back I think.

Sure man sounds great! I can hand you the balasts at the same time as well!

[Zac]

https://sl-i.net/FORUM/images/imported/2011/02/DSC00495-1.jpg

Whats going on here? Even Damien is interested!

[SOREN]

yeh. What IS going on there? I'm interested, and I'm not even Damien! :D

[Zac]

thats the grille from the accident, cracked down the bottom there.

Going to be gutting it all out, fix her up, Throw that honeycomb grille that I took off of a broken Mazda3 bumper behind it and painting it ABP like my car :)

[-J.M.G.-]

Some news?

[Zac]

not yet, still need to find my damn dremmel, and get some free time at work to get it started haha

[xoSubieLegacyxo]

not yet, still need to find my damn dremmel, and get some free time at work to get it started haha
I know how you feel. I started my light bar project in December, and I'm just now making the metal bracket in the following weeks! lol

[Zac]

I hate amber, decided it was time to get rid of it.

https://sl-i.net/FORUM/images/imported/2011/03/20110307183937_Edmonton_Alberta_CA-1.jpg
https://sl-i.net/FORUM/images/imported/2011/03/20110307185735_Edmonton_Alberta_CA-1.jpg
https://sl-i.net/FORUM/images/imported/2011/03/20110307190343_Edmonton_Alberta_CA-1.jpg
https://sl-i.net/FORUM/images/imported/2011/03/20110307190356_Edmonton_Alberta_CA-1.jpg
https://sl-i.net/FORUM/images/imported/2011/03/20110307192123_Edmonton_Alberta_CA-1.jpg
https://sl-i.net/FORUM/images/imported/2011/03/20110307192132_Edmonton_Alberta_CA-1.jpg
https://sl-i.net/FORUM/images/imported/2011/03/20110308105628-1.jpg

[BE-Fresh]

I'm diggin' it

[Zac]

thanks! A little darker then what I wanted but it will do :D

[SOREN]

Can't wait to see the new rims. Shall I spoil it? :D

[Zac]

Can't wait to see the new rims. Shall I spoil it? :D

as darth vader would say: NOOOOOOOOOOOOOOOOOO!!

I have them hid in a dark corner at work hehehe

[Zac]

https://sl-i.net/FORUM/images/imported/2011/04/5576199408_b354c63bd7-1.jpg (http://www.flickr.com/photos/grant_subaru/5576199408/)

Newest picture I have! haha

[Zac]

Finally got my summer rims thanks to SOREN! They are Prodrive GC-05A 17x7 +48

As you can see from this picture that this rim is curbed and will be sent out next week for fixing

I cant wait to get these on!

https://sl-i.net/FORUM/images/imported/2011/04/20110323075602-1.jpg

[httrdd]

I want them!

[SOREN]

Funny thing about that is that I actually have another pair! :D I was thinking of putting them on the STi this weekend, but ultimately glad I didn't, had a parking lot at the Zoo with a good 6 to 8 inches of snow in it today. The rest of the roads are dry.

Only rims I ever curbed too :( I was heading out to a JDM meet, made a right turn from a stop, and my GPS fell off. I lunged to grab it, and heard a crunch. So heartbroken to see how bad they got it. Rest of the rims are in good shape, and they will look VERY slick on Zac's car! I can't wait!

[Zac]

Well looks like I will have to wait even longer to put these on now :(

I have to somehow find $200 to buy all the pills I was prescribed yesterday and hopefully my insurance company will cover my physio therapy.

[SOREN]

Well looks like I will have to wait even longer to put these on now :(

I have to somehow find $200 to buy all the pills I was prescribed yesterday and hopefully my insurance company will cover my physio therapy.
Ahh, sucky deal man. At least you're getting some help though. Your insurance doesn't cover any medication??

It looks like it's going to be okay to roll on winters for a while longer though, I heard this AM that we're going to get 10 to 15cm of wet, sloppy snow coming up here soon.

[Zac]

Well looks like I will have to wait even longer to put these on now :(

I have to somehow find $200 to buy all the pills I was prescribed yesterday and hopefully my insurance company will cover my physio therapy.
Ahh, sucky deal man. At least you're getting some help though. Your insurance doesn't cover any medication??

It looks like it's going to be okay to roll on winters for a while longer though, I heard this AM that we're going to get 10 to 15cm of wet, sloppy snow coming up here soon.

My work benefits dont cause I took the smallest package, I have to call my insurance again tomorow and hopefully they can cover them as well with my physio, went tonight and got a bunch of forms to fill out.

[Zac]

Took it to the shop yesterday to clean it and started work on my grille! My old one broke from the accident so I started cutting it out and filling in the cracks and holes.

https://sl-i.net/FORUM/images/imported/2011/04/DSC00527-1.jpg
https://sl-i.net/FORUM/images/imported/2011/04/DSC00525-1.jpg
https://sl-i.net/FORUM/images/imported/2011/04/DSC00523-1.jpg

https://sl-i.net/FORUM/images/imported/2011/04/DSC00530-1.jpg
https://sl-i.net/FORUM/images/imported/2011/04/DSC00531-1.jpg
https://sl-i.net/FORUM/images/imported/2011/04/DSC00532-1.jpg

[ElbryanWolf]

Man I really love your wagon. Sad about the hit from the Acura, but the fix up went well I see and the upgrades keep on coming. :)

Keep it up.

Cheers

-Wolf-

[Zac]

Thanks ElbryanWolf!

Should have my prodrive rim back this week, then hopefully before friday i'll have them installed along with new timing belt, water pump and pulleys!!

[SOREN]

WANNA SEE THE RIMS..!

[Zac]

https://sl-i.net/FORUM/images/imported/2011/05/20110518133220-1.jpg

Just got it back today! Its so shiny and love the metalic in it! Definetly going to send the other 3 for repair over the winter :)

[SOREN]

wow! that looks really nice! I can't wait to see 'em on your car!!!!

[Zac]

Claybared and polished the other 3 on my lunch break so they are all shiny!

Getting them mounted tomorrow!!

[Zac]

https://sl-i.net/FORUM/images/imported/2010/07/20110520205849_Morinville_Alberta_CA-1.jpg

[Huffer]

Your parking is horrible! Take a better pic of the wheels... ;)

[ElbryanWolf]

I do love the car parked sideways with a Liquor store in the background ;) Priceless

The wheels are very nice though... very shinny :)

-Wolf-

[Zac]

Picking up boose before a bday part, trying to park like an ass and see how many spots I could take up :P

[Zac]

Got a new grille, finally got it prepped and painted yesterday.

Its made for a JDM Legacy 2.0GT so the fitment isnt the best but i'm just glad to get rid of the chrome.

https://sl-i.net/FORUM/images/imported/2011/07/20110630151552-1.jpg
https://sl-i.net/FORUM/images/imported/2011/07/20110630151952-1.jpg

[Danny-G]

i'm just glad to get rid of the chrome.
Amen to that. Be glad you're car didn't come with chrome door handles and trim like mine...

[Zac]

little update:

Got rid of the COBB SF Intake and put the stocker back on.

Drives so much smoother and no more lean issues :)

[chrish8r]

anything new man???? i just looked and saw nothing, i loved following this rebuild. you got a nice subie here

[Zac]

I'm back, thanks for thinking about me!

Some really bad events happened soon after my last update and now I am finally starting to get back on my feet.

If it weren't for my legacy and local Subaru club I really don't think I would be here right now.

Yes I have updates ill try to have them posted when I get home!

[xoSubieLegacyxo]

looks good!

[GTDrifter]

looking nice...keep up the good work

are those dual sti tips?

[Zac]

Cross posts from my WSC build thread:

so I finally finished painting the winter rims yesterday and went ahead and installed them today!

https://sl-i.net/FORUM/images/imported/2011/10/IMG_20111015_120728-1.jpg
https://sl-i.net/FORUM/images/imported/2011/10/IMG_20111016_131636-1.jpg

also wanted to do an oil change and remove the banjo bolt filter, was pretty tight and had to call Kenny for his assistance and his Masters in Physics and leverage saved the day!

First I went out and aquired the special dealer tool for the banjo bolt filter removal:
https://sl-i.net/FORUM/images/imported/2011/10/IMG_20111016_125416-1.jpg


After removing the turbo heatshield this is what it looked like underneath :-\
https://sl-i.net/FORUM/images/imported/2011/10/IMG_20111016_095304-2.jpg

Heres the filter, clean as a whistle with almost 150,000km on it, seems kinda fishy...
https://sl-i.net/FORUM/images/imported/2011/10/IMG_20111016_125906-2.jpg

So 2 top bolts were completly missing the nuts and the filter looked brand new, was the turbo replaced beforehand perhaps?

So when I got into my accident I ended up getting a whole new catback, after it was installed it was still leaking so it was sent out to an exhaust shop to fix the leak >:(
https://sl-i.net/FORUM/images/imported/2011/10/IMG_20111016_095353-2.jpg

My engine cover was only held on by 2 zip ties and I guess it had been vibrating enough to start eating away at the intake manifold so i'm on the lookout for an aftermarket belt cover.
https://sl-i.net/FORUM/images/imported/2011/10/IMG_20111016_141925-2.jpg
https://sl-i.net/FORUM/images/imported/2011/10/IMG_20111016_141918-1.jpg


Still trying to track down my rough idle issue, My year of legacy are known for having dirty injectors but another alternative is the oil control valves for the AVCS being all gummed up. I was able to pull the drivers side one out about half way, looked clean so I still suspect it is the injectors.

After I reconnected the battery and started it I ended up with a PO2016, TGV low voltage or something so i'll have to look into that too.

if anyone was wondering what or where the banjo bolt is its right ontop of the up-pipe stud in this picture.
https://sl-i.net/FORUM/images/imported/2011/10/IMG_20111022_111518-1.jpg

Broken TGV position sensor >:(
https://sl-i.net/FORUM/images/imported/2011/10/IMG_20111022_111537-2.jpg

[Zac]

looking nice...keep up the good work

are those dual sti tips?

Yes, STi Genome axle-backs

[chrish8r]

loving the pink wheels......dare to be different!!!!

[Zac]

loving the pink wheels......dare to be different!!!!

Haha thanks! They are just winter rims though!

Looking to sell or trade my prodrives for a set of 18' s though.

[Zac]

What a unsuccessful weekend. All I ended up doing is causing more damage.

Wish I knew before undertaking the TGV sensor replacement that theres not enough room between the IM and turbo to pull it off the spline so its staying like this until I can afford TGV deletes and my car towed down to sunny for a protune (TGV deletes without a tune puts the car in limp mode >:( )

https://sl-i.net/FORUM/images/imported/2011/11/IMG_20111105_125312-1.jpg

Also the roofers at work dropped a 2x4 on my car. Yay more dents!!

https://sl-i.net/FORUM/images/imported/2011/11/IMG_20111106_082708-1.jpg

[lord flashheart]

ouch... at least it didnt do a ton of damage.. could be worse.

[Zac]

$1700 in damages.

Hoping I can get it in cash then do the work myself for free :D

[chrish8r]

Its more rewarding when you do the work yourself also.....haha

[Zac]

I work in a body shop anyways :D

My drivers and pass side doors are peeling around the door handles (bad prepping)

So those are getting repainted under warrenty, so while its all appart i'll fix the fender and hood, probablly next summer.

So if I get cash clutch+flywheel are going in.

[Zac]

Had a friend do a T-belt change and coolant flush on my wagon thursday night. at about 151,000KM, belt had 3 cracks in it, 2 idlers were making noise and the tensioner was leaking a little. Definetly happy I had it done sooner then later. Broke a nipple on my rad so a quick fix until I am able to order a Mishimoto one.

https://sl-i.net/FORUM/images/imported/2012/01/IMG_20120105_191306-1.jpg
https://sl-i.net/FORUM/images/imported/2012/01/IMG_20120105_195744-1.jpg
https://sl-i.net/FORUM/images/imported/2012/01/IMG_20120105_201212-1.jpg
https://sl-i.net/FORUM/images/imported/2012/01/IMG_20120105_205801-2.jpg
https://sl-i.net/FORUM/images/imported/2012/01/IMG_20120105_225532-2.jpg

[chuckthefuk]

I hate plastic rads!! Glad to hear ur in tip top shape.

[Zac]

I hate plastic rads!! Glad to hear ur in tip top shape.

Thanks buddy! Feels like i'm back on my feet finally!

More goodies to come this year, I was supposed to order a clutch and flywheel next month but the Rad is setting me back $300 or so, Still dont know what my goals are for this car yet, Ultimately I want the best reliability possible.

[Zac]

this sound has pretty much got me sold on going twinscroll

http://www.youtube.com/watch?v=U8w7848kF1E

[Zac]

So my quick rad repair let go last night, Mishimoto is in the post!

Also picked up a used VF46 with an AVO 15PSI actuator, contemplating sending it out to Grimmspeed for a PNP

Finally making some build progress :)

[Zac]

http://a4.sphotos.ak.fbcdn.net/hphotos-ak-ash4/403314_10150795973333976_511108975_12295864_125173024_n.jpg
http://a8.sphotos.ak.fbcdn.net/hphotos-ak-ash4/402053_10150795973533976_511108975_12295866_1646658147_n.jpg

VF46 with AVO 15psi wastegate actuator

Parts are starting to roll in >:D

[Zac]

I know nobody gives a fuck about BL/BP Legacys but i'll keep posting here anyways.

Rad was installed thursday. Definetly spend the extra money on the slim fans for more piece of mind, My friend had to make a little bracket to hold the upper rad hose away from the stock fans.

http://a2.sphotos.ak.fbcdn.net/hphotos-ak-ash4/428754_10150815162638976_511108975_12357808_1111759563_n.jpg
http://a3.sphotos.ak.fbcdn.net/hphotos-ak-snc7/428604_10150815163208976_511108975_12357810_477784754_n.jpg
http://a8.sphotos.ak.fbcdn.net/hphotos-ak-snc7/417625_10150815163798976_511108975_12357816_1869121520_n.jpg
http://a2.sphotos.ak.fbcdn.net/hphotos-ak-ash4/429810_10150815164208976_511108975_12357817_1755670496_n.jpg
http://a2.sphotos.ak.fbcdn.net/hphotos-ak-ash4/426646_10150815164663976_511108975_12357820_648140678_n.jpg

[chuckthefuk]

People care!

Looking good.. so whats the breakdown of this turbo build?

[xoSubieLegacyxo]

I know nobody gives a fudge about BL/BP Legacys but i'll keep posting here anyways.

THAT'S NOT TRUE! I want to get a 4th Gen LGT in the near future. Keep posting on SLi!

[Zac]

People care!

Looking good.. so whats the breakdown of this turbo build?

Not really a turbo build, just bought a replacement turbo since our stock VF40's tend to blow.

Trying to get all the maintenance done and run a healthy stage 2 setup so I can focus on suspension and creature comfort mods.

[chuckthefuk]

FMIC down the line?

[Zac]

FMIC down the line?

Never.

[chrish8r]

i would love to have one of these turbo leggys. really good body lines. glad to see a tastefully modded one

[ElbryanWolf]

Ok so you didn't re-use the original fan assembly with the new rad?

Also, never realized we had plastic rads in ou BL/BPs ;) I'll know to make the change if I pop a leak as well. How expensive was it (rad + new fans + needed parts)? Is it an easy DIY or you need professionnal help? How long did it take?

Thanks

-Wolf-

[Zac]

Ok so you didn't re-use the original fan assembly with the new rad?

Also, never realized we had plastic rads in ou BL/BPs ;) I'll know to make the change if I pop a leak as well. How expensive was it (rad + new fans + needed parts)? Is it an easy DIY or you need professionnal help? How long did it take?

Thanks

-Wolf-

Yes I reused the stock fan assembly and overflow tank, I wish I would have bought the slim fans since there isnt much room.

The rad itself was about $300 shipped.

Had a friend help me out, its pretty straight forward, again it would have been a lot easiyer if you buy the slim fan kit.

[Zac]

i would love to have one of these turbo leggys. really good body lines. glad to see a tastefully modded one

Thank you, starting next month I'm going to be a hermit so I can have this car all built before summer :grin:

[Tylerhartman]

I Only dream of having a 4th gen GT Wagon some day ;) Nicely done!

[blanquelm92]

Man.......that exhaust looked like it was bent like hell......damn acuras.....
Dude tell me about it I got hit by a damn rsx while waiting for
A train :smt013

[Zac]

Got me some Rotella and a STi Catless up pipe

http://a8.sphotos.ak.fbcdn.net/hphotos-ak-ash3/550149_10150964382463976_511108975_12875759_956166137_n.jpg

[nikolaus.conrad]

Very cool wagon! I wish to own a 4th gen GT someday. Keep us updated on progress!!

[Zac]

Very cool wagon! I wish to own a 4th gen GT someday. Keep us updated on progress!!

Thanks!

Did an oil change yesterday, swapped on the Prodrives and fixed my skidplate.

Going to a BBQ with the Lancer club today so I put 3 coats of wax on her, should have some sweet pics later!

[Zac]

So I'm picking up a ebay replica Tomei EL header tomorow.

Before you argue with me read everything i've linked here:

http://www.westernsubaruclub.com/smf/in ... ic=29518.0 (http://www.westernsubaruclub.com/smf/index.php?topic=29518.0)

[Grafton]

why argue? EL's are for more power both in NA and boosted Subaru's.

[Zac]

why argue? EL's are for more power both in NA and boosted Subaru's.

People argue about losing the boxer rumble and such, porting stock headers are better blah blah

[Zac]

So I picked up a used EL header last weekend, It looks like some sort of Tomei Replica, welds look great, piping size doesnt seem to thin so I went for it.

It was wrapped and used for about 5000km or so the previous owner said, I decided to take the wrap off and just coat it to help its longivity.

https://sl-i.net/FORUM/images/imported/2012/07/IMG_20120703_101905-1.jpg

Sanded the whole thing with 80 grit and masked off the flanges

https://sl-i.net/FORUM/images/imported/2012/07/IMG_20120707_143341-1.jpg

Primed

https://sl-i.net/FORUM/images/imported/2012/07/IMG_20120707_150445-1.jpg

Painted

https://sl-i.net/FORUM/images/imported/2012/07/IMG_20120707_155633-1.jpg
https://sl-i.net/FORUM/images/imported/2012/07/IMG_20120707_161031-1.jpg

Needed new springs for the slip joint, found these at Cambodian tire

https://sl-i.net/FORUM/images/imported/2012/07/IMG_20120707_164104-1.jpg
https://sl-i.net/FORUM/images/imported/2012/07/IMG_20120707_164404-1.jpg

[chrish8r]

Did you get a chance to get this EL header on? Im curious of how it sounds. Ive heard different stories about them....

[Zac]

Actually sold it too a buddy who put it on his 02 wrx rally car, after hearing it I regretted my decision immidietly.

In the end I didn't want to have a header that would need replacing down the road as all aftermarket headers besides the KillerB one will crack eventually.

[Zac]

Little update:

Ordered a Spec Stage2+ Clutch.

[Zac]

So I got the wrong clutch and blah blah had to make a huge re order.

Group N Rear Shifter Bushing
Group N Transmission Crossmember Bushing Kit
Group N 5-Speed Trans Mount
Kartboy 5-Speed Shifer Bushings
SPEC Stage 2+ Legacy GT Clutch Kit
Subaru 75W90 Extra-S Gear & Transmission Fluid
Subaru Manual Transmission Drain Plug Washer
Torx Plus TP50 Bit

Also I have my Spec Lightweight flywheel, should take pics soon.

[Zac]

Got my Spec Dual Mass flywheel a little while back

http://a2.sphotos.ak.fbcdn.net/hphotos-ak-ash3/s720x720/561036_10151400024143976_1767326924_n.jpg

[chuckthefuk]

mmmmmmm so nice!!! love it!!

[Dead91silvia]

Why didnt you upgrade to an 07 solid Flywheel/clutch setup? I did that for one of my customers with an 05 XT OB and he loves it!

Just wondering...

[Zac]

That was the original plan as I had purchased a Spec Stage2+ for 06 wrx fitment.

The same seller that sold me that clutch also sold me the flywheel but he thought it was a single mass one. And since I am in Canada I got raped on postage so I am sending back the clutch so it would be cheaper.

All in all I'm kinda glad I'm sticking Dual mass, I live in a city and have a huge road trip planned next year so the dual mass will suit my needs better.

[Zac]

http://sphotos-e.ak.fbcdn.net/hphotos-ak-ash4/247969_10151438773353976_937977611_n.jpg
http://sphotos-c.ak.fbcdn.net/hphotos-ak-ash4/317510_10151438773398976_1523886793_n.jpg
http://sphotos-f.ak.fbcdn.net/hphotos-ak-prn1/550652_10151438773453976_738658111_n.jpg
https://sl-i.net/FORUM/images/imported/2012/10/326795_4838087469837_1750257034_o-1.jpg
https://sl-i.net/FORUM/images/imported/2012/10/286972_4838084509763_447603305_o-1.jpg
https://sl-i.net/FORUM/images/imported/2012/10/258628_4838086669817_1806506614_o-1.jpg
https://sl-i.net/FORUM/images/imported/2012/10/244071_4838088069852_1442841846_o-1.jpg
https://sl-i.net/FORUM/images/imported/2012/10/241543_4838087189830_270444464_o-1.jpg
https://sl-i.net/FORUM/images/imported/2012/10/240460_4838085589790_7045452_o-1.jpg
https://sl-i.net/FORUM/images/imported/2012/10/204741_4836807357835_227563132_o-1.jpg
https://sl-i.net/FORUM/images/imported/2012/10/193732_4838085829796_188580749_o-1.jpg
https://sl-i.net/FORUM/images/imported/2012/10/176880_4838084869772_1608353798_o-1.jpg
https://sl-i.net/FORUM/images/imported/2012/10/175021_4838088749869_1920932365_o-1.jpg
https://sl-i.net/FORUM/images/imported/2012/10/51848_4836808917874_1992427378_o-1.jpg

[Zac]

Re-uploaded Clutch install pics on my Photobucket

[chuckthefuk]

ha za!!

[Zac]

http://sphotos-b.ak.fbcdn.net/hphotos-ak-ash3/532613_10151551364848976_1131311101_n.jpg

Is now Stage 1

[chuckthefuk]

Yes.. ! ... more info please.

[Zac]

Yes.. ! ... more info please.

Hard to tell, whenever it hits boost all I get is wheelspin in this weather ;)

Overall its a great mod, drivability is much better, smoother drive by wire.

What I love the best is how it holds the wastegate closed until it hits target boost so ultimately you get much faster spool up and a huge rush of power at once, I can see why they werent tuned like this from factory :D

[chuckthefuk]

Thats one of the best COBB AP descriptions I have ever heard... sounds like a blast :-D

What PSI is it set to?

[Zac]

Thats one of the best COBB AP descriptions I have ever heard... sounds like a blast :-D

What PSI is it set to?

15psi

On my logs I have only hit 14.4 due to slippery roads, I think tonite i'll go around the city to see if I can find a place where I can get the car under full load to see if it actually hits that high.

[Zac]

Bought some 06 SpecB rims as a Xmas present to myself

https://sl-i.net/FORUM/images/imported/2013/01/8xiNo-1.jpg

Got them for very cheap since the PO thinks 2 of them are bent but I have some hookups through work to check them out to see if they need any repair.

Tire plans are 225/40/R18 Michelin Pilot Super Sports

My Prodrives are now for sale.

[chuckthefuk]

Sex! how much for the prodrives?

[Zac]

Sex! how much for the prodrives?

Was hoping to get $1000 for them with the tires.

[chuckthefuk]

You still living in the boonies? If so.. whats the shipping going to be on these?

I can take a 18 hour there and back journey for 17" lol

[Zac]

You still living in the boonies? If so.. whats the shipping going to be on these?

I can take a 18 hour there and back journey for 17" lol

No I've been in Alberta for 3 years now! haha

[chuckthefuk]

Ouch.. come back to Ontario... We have cookies!!

[Zac]

Ouch.. come back to Ontario... We have cookies!!

Hey I actually switched over to body work, well I'm doing prep actually, you have a autobody shop right? Get me a job and i'll be there! lol

[chuckthefuk]

:-( I did .. 3 years ago before my father passed away.. Thats why my track project is crawling to completion .

I am glad you part of the "death by lung complication" industry. Its rewarding when you turn devastation into factory finish.

[Zac]

:-( I did .. 3 years ago before my father passed away.. Thats why my track project is crawling to completion .

I am glad you part of the "death by lung complication" industry. Its rewarding when you turn devastation into factory finish.

I do my best to protect myself, Everyday I see guys younger then 30 sanding without a mask on, it boggles my mind.

[chuckthefuk]

Fast Pass life style.. no time for safety.. same with eye protection... I cant stand ppl using cut off wheels without face protection.. I've had a few disc explode on me and the aftermath takes weeks to heal.

Anyways glad your Legacy is getting better and better!

Cheers to life and modifications!
-Chuck

[Zac]

https://sl-i.net/FORUM/images/imported/2013/02/UCCsVkH-1.jpg

Legacy SpecB Revision A Bilsteins and springs

The stiffest setup Subaru ever made from factory for my generation of Legacy. They need some TLC lucky for me my new shop also has a powder coating oven!

[amgarrety]

I love those SpecB rims. I want a set so bad but I just don't have the cash. That is why I chose to go with P1s, they are along the same lines as the SpecB rims style-wise.

[Zac]

I love those SpecB rims. I want a set so bad but I just don't have the cash. That is why I chose to go with P1s, they are along the same lines as the SpecB rims style-wise.

Would you believe I picked these up for $450 shipped? Keep an eye out on legacygt.com in the wheels for sale section, Want a Prodrive Shift knob? I no longer need it! lol

I need some opignions, I accendentally ripped my rear seats when transporting my tool box to my new shop, For a while I wanted to convert to a newer SpecB interior, blue alcacantra similar to STi's or we got the weird red colour in 2006.

https://sl-i.net/FORUM/images/imported/2013/02/1434822lg-1.jpg

http://img2.netcarshow.com/Subaru-Legacy_2.5_GT_spec_B_2007_1280x960_wallpaper_05.jpg

[chuckthefuk]

The red is so hawt. Why not custom alcacantre inserts ?

[Zac]

The red is so hawt. Why not custom alcacantre inserts ?

Leaning towards that due to cost :lol:

I want to try to modify my drivers seat for more bolster and theres a spring thats pushing really hard on my bottom that needs to be fixed :roll:

Although my back is still messed up from my car accident, the Legacy seats were very umcomfortable on my last 6 hour trip, im hoping I can fix that some how

[chuckthefuk]

Foam glue and patience will correct all ur back and ass pain.
Hehhehehhehe

[Zac]

https://sl-i.net/FORUM/images/imported/2013/03/aD0c6cxjpg1-1.jpg
https://sl-i.net/FORUM/images/imported/2013/03/KEPpu4A-1.jpg
https://sl-i.net/FORUM/images/imported/2013/03/lmAm8su-1.jpg

:D

[Zac]

BFGoodrich G-Force Sport Comp2's ordered, $780

Rust repair quote for driver's 1/4 is going to be near $2000

Sending Rims out for repair, should be around $500

Powder coating at my shop, should only be $30 of material.

$3310

Damn why cant I have a cheaper hobby

[chuckthefuk]

because cheap hobbies are for the weak and the lame.

More power to you!!

[Grimmrican]

^^Amen lol

[Zac]

Oh I just cant stop spending, Must be summer time!!

Subaru Legacy Engine Cover Clips 909130051 6
Subaru NGK Iridium Spark Plugs For Legacy GT 22401AA670 1
Subaru Legacy Spec B Front Strut Mounts 20320AG01A 2
Subaru Legacy GT Front Wheel Bearing 28373AG01A 1
Subaru Axle Nut 902170049 1

[Zac]

ill just post these here :smile:

https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-prn1/547623_10151859477578976_775841418_n.jpg
https://fbcdn-sphotos-g-a.akamaihd.net/hphotos-ak-ash3/547244_10151859575338976_2041952028_n.jpg
https://fbcdn-sphotos-g-a.akamaihd.net/hphotos-ak-ash3/936988_10151862216743976_227748276_n.jpg

[Zac]

Rust fixed :)

https://sl-i.net/FORUM/images/imported/2013/04/IMG_6694_zpsc1033775-1.jpg
https://sl-i.net/FORUM/images/imported/2013/04/IMG_6574_zpsa03e8863-1.jpg
https://sl-i.net/FORUM/images/imported/2013/04/IMG_5604_zps1c2dd007-1.jpg
https://sl-i.net/FORUM/images/imported/2013/04/IMG_4292_zps4f85af93-1.jpg
https://sl-i.net/FORUM/images/imported/2013/04/IMG_9227_zps0e29ed28-1.jpg
https://sl-i.net/FORUM/images/imported/2013/04/IMG_9832_zps67f453f9-1.jpg
https://sl-i.net/FORUM/images/imported/2013/04/IMG_4690_zpsf65c003c-1.jpg

[chuckthefuk]

Clean!

[Tylerhartman]

nice, That's my old outback needed... expect for the fact the repair job would be more then I paid for the whole car haha :) They did a nice job, sweet leggy.

[Zac]

https://sl-i.net/FORUM/images/imported/2013/05/20130525_124010_zpsfd42595a-1.jpg
https://sl-i.net/FORUM/images/imported/2013/05/20130525_140221_zps0cfd1312-1.jpg

Really happy how the car feels now, super firm but also absorbs dips and potholes nicely.

[Zac]

HUGE UPDATES, Havent been around much due to work but here goes.

In July I finally got some track time!


Got the Technafit steel braided brake lines, Grimmspeed Master cylinder brace installed and flushed with ATE Super Blue fluid, Made quite the difference and am very pleased with the purchase.

https://sl-i.net/FORUM/images/imported/2013/12/20130724_192616_zpsff742063jpgoriginal-1.jpg

Finally felt like the car was ready for the track so I bought this:
https://sl-i.net/FORUM/images/imported/2013/12/20130724_123146_zps1f7e3355jpgoriginal-1.jpg

Out at Stratotech yesterday:
https://sl-i.net/FORUM/images/imported/2013/12/1006015_10201094365954548_502126161_n_zp-1.jpg
https://sl-i.net/FORUM/images/imported/2013/12/20130727_181350_zps43c21f80jpgoriginal-1.jpg

More parts bought waiting to be installed, finally got around to it at Xmas
https://sl-i.net/FORUM/images/imported/2013/12/20131028_111527_zpsab23e054jpgoriginal-1.jpg


So just before Xmas I developed some weird problems with my car lurching or stumbling while cruising so I canceled my plans and decided it was time to fix the car:

Let's get down to buisness
https://sl-i.net/FORUM/images/imported/2013/12/20131224_161758_zpsf46f3e79jpgoriginal-1.jpg

Intake Manifold off *note I highly suggest you don't do this drunk so you have a little bit of a clue when you go to reinstall all the Vacuum lines and such*
https://sl-i.net/FORUM/images/imported/2013/12/20131224_194657_zps945beeb3jpgoriginal-1.jpg

IM off, Cleaned it out with brake clean as much as possible
https://sl-i.net/FORUM/images/imported/2013/12/20131224_194714_zpsaeccf5dfjpgoriginal-1.jpg

Torquing the TGV deletes
https://sl-i.net/FORUM/images/imported/2013/12/20131225_134247_zps91f1462djpgoriginal-1.jpg

All back together!
https://sl-i.net/FORUM/images/imported/2013/12/20131228_104301_zps07a380bc-1.jpg

New Turbo inlet takes a lot of room so MAP is just hanging there and had to reroute the PCV and Wastegate solenoids underneath the IM.
https://sl-i.net/FORUM/images/imported/2013/12/20131228_104308_zpseacd599ajpgoriginal-1.jpg

[Zac]

Took part in a Rallycross few weekends ago, had a lot of fun and ended up getting 2nd place in Novice 4WD

https://sl-i.net/FORUM/images/imported/2014/03/12576505244_5f0da48d81_h_zps5d9f1240jpgo-1.jpg
https://sl-i.net/FORUM/images/imported/2014/03/12577312373_a120551684_h_zps1c2d7b2ejpgo-1.jpg
https://sl-i.net/FORUM/images/imported/2014/03/12576157183_080684c5e7_h_zpscde52f0ejpgo-1.jpg
https://sl-i.net/FORUM/images/imported/2014/03/12576148593_4cfe28af07_h_zps5d5a6a18jpgo-1.jpg

Also I have some JDM Aero spats and a BaysonR front lip in my room waiting for spring to install.

[chrish8r]

That looks like a ton of fun!!! Especially with all the snow.