I need instructions on how to install whiteline rsb for BH.

[SativaMan04]

Hi guys,

I am super broke and I want to get my swaybar installed. I've had it for about 2 weeks now and I really don't want to wait for my next 2 checks to have a shop install it. So I was wondering if I can get some help? I really need step by step instructions on how to install my whiteline swaybar on my Bh.

I don't have a lot of tools so I might have to buy/borrow some. I would say my mechanical skills are very low, but I have the whole weekend so I think I can do it in that timeframe. I envy all you mechanically inclined brothers here! I'm excited to try it, but nervous at the same time. hehe

Thanks Guys!

:smt025

[GTDrifter]

https://sl-i.net/FORUM/viewtopic.php?f=39&t=5094&hilit=rear+sway+bar+install

[GTDrifter]

you dont really have to remove the tires but it makes it easier to access, I usually just put the rear of the car on ramps and crawl underneath

[SativaMan04]

Thanks GT. I'll read it right now!

[SativaMan04]

Couple questions. I dont have any grease. What kind can I buy? Are there little packets so I don't have to buy a big container? When I do grease the bushings, do I grease the inside and outside of it? Or just the inside where bar sits?

Also, When I put the car on jack stands, do I have to leave the E-Brake locked or unlocked? I know I have to put the car in first gear to prevent it from rolling.

Thanks Again.

[GTDrifter]

Lock ebrake and put a block infront of the front wheel just in case, I didn't use grease and its been fine

[chuckthefuk]

Any automotive store "parts source/auto zone/pep boys" will sell small tubes of silicon grease or rubber safe grease applications.

Shouldn't cost you more then $10 for a tube...

-Chuck

[SativaMan04]

Any automotive store "parts source/auto zone/pep boys" will sell small tubes of silicon grease or rubber safe grease applications.

Shouldn't cost you more then $10 for a tube...

-Chuck

So when I grease the bushings, do I only grease the inside of it where it meets the bar or the outside as well where it meets the bracket?

[chuckthefuk]

Outside and inside. Any surface area that will have movement or pivoting .. Inner diameter and where the bracket meets is sufficient.

https://sl-i.net/FORUM/images/imported/2012/01/1830666353_25df364e00-2.jpg

https://sl-i.net/FORUM/images/imported/2012/01/1830668763_ab8b3ed2a8-2.jpg

Also any non-petroleum based grease will work.. Some people use lithium grease..

[SativaMan04]

Awesome!

[r3v_v3ng3]

Where you at in norcal? I can help if you live nearby

[SativaMan04]

Where you at in norcal? I can help if you live nearby

That would be awesome but I'm actually in the 408 San Jose area. I can definitely use some help and You're more than welcome to come by, but I know you're like an hour away and time is valuable.

[Bhatman]

Where you at in norcal? I can help if you live nearby

That would be awesome but I'm actually in the 408 San Jose area. I can definitely use some help and You're more than welcome to come by, but I know you're like an hour away and time is valuable.

If help is needed, I can offer on doing the RSB (im located over in 510). I did the whiteline install on my BH last year, its pretty straight forward to do, just make sure you have a good extension to break the endlink bolts.

[SativaMan04]

pm

[r3v_v3ng3]

That would be awesome but I'm actually in the 408 San Jose area. I can definitely use some help and You're more than welcome to come by, but I know you're like an hour away and time is valuable.


Yeah your like an hour and a half. It would be better if you bring it over to my house cause i have all the tools but for the amount of gas/time it would be the same as paying someone to do it.

Bhatman is more closer to you and have the experience :smt023