Dead91silvia
03-07-2012, 08:15 PM
I have no idea what to call this thing! hahaha
Skill level 1-5
Level 1-2 A challenge for a beginner, but not too hard.
Anyway, I had this idea ever since I got my SLi sticker's and this was something I have been wanting to do and just got it all done. Took me about 20 minutes to make...
CHECK LOCAL LAWS! THIS MIGHT BE ILLEGAL IN YOUR STATE!
(it is in WA... shhh... dont tell anyone!) :smt027
I know that some states dont have a front plate law, I know WA does have a front plate law, but I have never got flack about it, or at least in the last 4 years. They leave me alone. Also JDM plates have different widths so you have to build or modify something to make them work. We will just say I'm a rebel and dont like to run a front plate. :grin:
Some of you have seen my Carbon Fiber spare tire cover I made from an old Honda Civic hood. Well, I still have some hood left to play with...
This is one of the smaller sections I have left of the hood... I made a cardboard template to get a rough idea of what I needed. Worked well!
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8835-1.jpg
Then measured all edges to make sure they were the same...
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8837-1.jpg
I used a cut off wheel to cut it, works great! Just make sure you use a dust mask! You can also use a Dremel...
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8838-1.jpg
This is what I ended up with... Also cut the back side since C/F is not to flexible when it's clear-coated...
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8839-1.jpg
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8840-1.jpg
Measure for your holes, you only got one shot so make it count! I held it to the front of the bumper and used a sharpy
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8843-1.jpg
I got some nice fasteners to mount it. JDM and USDM bumpers are a little different, but same idea.
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8841-1.jpg
Apply sticker and shazam! You got something cool!
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8844-1.jpg
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8845-1.jpg
Now this is not the most hard thing to make and it was kinda fun! Took me about 20 minutes!
I dont have any pics of it, but I did round the edges and sanded the flat sides so it didnt have a sharp edge on it, but I;m sure you can figure it out! :smt023
Skill level 1-5
Level 1-2 A challenge for a beginner, but not too hard.
Anyway, I had this idea ever since I got my SLi sticker's and this was something I have been wanting to do and just got it all done. Took me about 20 minutes to make...
CHECK LOCAL LAWS! THIS MIGHT BE ILLEGAL IN YOUR STATE!
(it is in WA... shhh... dont tell anyone!) :smt027
I know that some states dont have a front plate law, I know WA does have a front plate law, but I have never got flack about it, or at least in the last 4 years. They leave me alone. Also JDM plates have different widths so you have to build or modify something to make them work. We will just say I'm a rebel and dont like to run a front plate. :grin:
Some of you have seen my Carbon Fiber spare tire cover I made from an old Honda Civic hood. Well, I still have some hood left to play with...
This is one of the smaller sections I have left of the hood... I made a cardboard template to get a rough idea of what I needed. Worked well!
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8835-1.jpg
Then measured all edges to make sure they were the same...
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8837-1.jpg
I used a cut off wheel to cut it, works great! Just make sure you use a dust mask! You can also use a Dremel...
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8838-1.jpg
This is what I ended up with... Also cut the back side since C/F is not to flexible when it's clear-coated...
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8839-1.jpg
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8840-1.jpg
Measure for your holes, you only got one shot so make it count! I held it to the front of the bumper and used a sharpy
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8843-1.jpg
I got some nice fasteners to mount it. JDM and USDM bumpers are a little different, but same idea.
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8841-1.jpg
Apply sticker and shazam! You got something cool!
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8844-1.jpg
https://sl-i.net/FORUM/images/imported/2012/03/IMG_8845-1.jpg
Now this is not the most hard thing to make and it was kinda fun! Took me about 20 minutes!
I dont have any pics of it, but I did round the edges and sanded the flat sides so it didnt have a sharp edge on it, but I;m sure you can figure it out! :smt023