2000 Subaru Legacy GT Limited TURBO Project

My friend and I are aquiring parts to turbo his 2000 Legacy GT limited.
here are the parts we have so far:

02 WRX turbo
http://memimage.cardomain.net/member...2151204_28.jpg
02 WRX TMIC
http://memimage.cardomain.net/member...2151204_27.jpg
02 WRX bov
http://memimage.cardomain.net/member...2151204_20.jpg
04 WRX Fuel Pump
05 STI Injectors and Fuel Rails
http://memimage.cardomain.net/member...2151204_23.jpg
01 2.5RS JDM Turbo Manifold (STI RA)
http://memimage.cardomain.net/member...2151204_10.jpg
Black Greddy Turbo Timer + Harness
http://memimage.cardomain.net/member...2151204_30.jpg
Greddy Emanage, harness and support tool
http://memimage.cardomain.net/member...04_21_full.jpg

What parts should i look into getting next? I'm not in a rush to put this all together so any input would be greatly appreciated as my friend and i are big noobs when it comes to anything turbo charged. We've really been trying to research this project and have been saving up a good amount of cash for it so please post up some helpful comments!

Here is a mod list of the car as it stands right now:

Gripforce Stage 3 Clutch
Fidanza Flywheel (9.5lbs)
2.5rs Intake
NGK Iridium IX Plugs
Lightweight Underdriven Crank Pulley
Custom Cat back exhaust & Muffler
KYB-2 Gas-ChargedStruts
17" ADR Sokudo wheels
Sumitomo ZR rated tires
Bomz Short throw shifter

http://www.cardomain.com/ride/2151204/2

Here are some pictures of the parts I have aquired so far. I am still looking for a hood scoop, and y-pipe for the intercooler. If I have any glaring mistakes in my list, let me know, thanks, and any suggestions will be greatly appreciated. Where should I get it installed? I'm in upstate NY, 5 hrs from NYC and 5 hrs from Toronto. Thanks

I'd like to see how it turns out :wink:

BTW, welcome to SLi

I've heard that Toronto has some good shops. I'd get an STi shortblock to go with all this stuff (1800 bucks new) because the Standard EJ25 isn't terribly strong.

You did eliminate the first weak point in boosting an N/A engine by getting the fuel rails/injectors, etc.

^^ Providing boost is limited, he'd have no problems with it.

Are you getting a custom exhaust system made up? You may have to, unless you decide to use a WRX one, and you may run into problems with the engine crossmember blocking the WRX exhaust.

I would try test fitting the STi RA one before you begin anything.
You might want to get some gauges.

Do a compression test on the engine too, just to give yourself a benchmark.

Quote:

---

Originally Posted by Huffer

^^ Providing boost is limited, he'd have no problems with it.

---

That's not how boost works though...once you get some, you only want more :lol:

Quote:

---

Originally Posted by Huffer

Do a compression test on the engine too, just to give yourself a benchmark.

---

And a dyno run!

thanks for all the replies guys. I have a good friend that is going to make my 3" custom Stainless steel exhaust. We're going to try for 7psi to start, and if somebody has the link to the STI shortblock, please post it here. Also, if anybody has been to a good shop in toronto that does the work cheaply and well, that would be greatly appriciated. For gauges, to save money, we're going to use a laptop with digital gauges at first (plugged into the emanage). We hope to get the turbo in soon.

Very cool, man! :smt023

As for 7psi, you should be good, provided you do that with the new fuel system in. Watch the A/F ratio VERY closely the first few months, @ 7psi, fuel is going to be the danger to the stock block.

As for the STi block, I quoted you a dealer price for the shortblock (not the longblock).

Here's a link as well:
http://www.slowboyracing.com/shop.php?c ... f0a25ec8f4

As for shops...hmmm, GTWagon is in Canada, as well as BGWagon, and Cajual. Try PMing one of them.

don't forget:

up pipe
down pipe
turbo crossmember
boost controller (oem, mechanical or electrical like Prodrive or Perrin)
some sort of aftermarket intake

we dont need a down pipe because its a TMIC, we do need an up pipe. The boost controller is in the greddy emanage. I dont know what we're going to do about the intake right now, and what is the crossmember.

Quote:

---

Originally Posted by legacy25gt

we dont need a down pipe because its a TMIC, we do need an up pipe. The boost controller is in the greddy emanage. I dont know what we're going to do about the intake right now, and what is the crossmember.

---

yes, you will need a down pipe. It has NOTHING to do with the TMIC...it has everything to do with taking the exhaust OUT of the turbo and DOWN to the midpipe and out the muffler.

The UP PIPE brings the exhaust UP from the exhaust manifold, thru the turbo and the DOWN PIPE bring the used exhaust gases out of the turbo and DOWN to the regular exhaust system under the car....thus the DOWN-ward motion.

And the crossmember is the engine cradle, support member.
http://sportcompactcarweb.com/tech/0...hybrid04_z.jpg The black one is the type you want, it has the recess to allow the uppipe between the motor and the crossmember. The gray type is what you'll be taking out of the 00 Legacy.

Cars that have the 'Turbo Crossmember' are as follows:

90-94 Legacy Turbo
02-06 WRX
04-06 WRX STI
05-06 Legacy 2.5GT
04-06 Forester XT
and the Baja-Turbo has it as well....don't know the limited run that car had.

Now, someone (I forget who, don't take offense) modified their non-turbo crossmember and welded a pocket or recess for the uppipe to fit in.

matt

Thanks for the clarification. I was thinking about using a flex up pipe and down pipe, but I was wondering if there were any complications with mounting brackets of the engine, or L-brackets that would block the up pipe, or will that engine cradle support member let it fit? thanks

flex pipe for exhaust?

ick, no, have a shop bend piping for you.

should I just have a shop make both pipes, and will out exhaust manifold be a direct bolt on to the 00 legacy ej25 engine?

I would think you can use WRX or STi UP/DP assemblies that are pre-fabbed.

will our exhaust manifold need to be modified or will it be a direct bolt on?

Quote:

---

Originally Posted by legacy25gt

will our exhaust manifold need to be modified or will it be a direct bolt on?

---

Not entirely sure, honestly. I'm pretty sure it's the same for all EJ engines.

if you use a turbo cross member, and that exhaust manifold, any after market up pipe for a wrx will fit.

will the legacy stock intake manifold work with the boost I am pushing?

Quote:

---

Originally Posted by legacy25gt

will the legacy stock intake manifold work with the boost I am pushing?

---

Yes. I'm using a stock intake manifold off of a NA 2.5 Forester.

I'll be joing you soon :D

6psi only though, w/ a 14lb flywheel, using a greddy emanage ultimate. I'm not sure if the 9.5lb is too light for the NA 2.5...

https://sl-i.net/FORUM/images/import...HPIM0433-2.jpg

That is so much stuff and $$$! I wonder how this turned out? Ben, will you have to get all this stuff?

everything but the EM is paid for...so ugh yeah I'm sorta broke :D

Forgot to add, don't get a boost controller, especially a manual. Those things can be so finicky that a 1/50 turn of the knob can mean a difference of 7psi to 10 psi. Not good for the small window of boost our engines can take.

Use the wastegate to control your boost; is that turbo coming from a WRX? I thought the wastegate opens at 10psi...better check on that. Wouldn't want to overboost your engine even before everything is in place; look in rs25.com to see how to adapt a 5psi wastegate spring.

What kind of power will the 2.5 make with 6psi of boost?

Quote:

---

Originally Posted by smoke3006

What kind of power will the 2.5 make with 6psi of boost?

---

With a TMIC, it's going to be roughly 100hp over stock w/ a proper tune (so around 260 bhp, 212whp; out of the box it makes more than a standard ej20t swap and with a flatter torque curve due to displacement). That's the quote numbers from the AVO turbokit, which runs 6 psi I think.

Quote:

---

Originally Posted by rougeben83

With a TMIC, it's going to be roughly 100hp over stock

---

:shock: hmmm....

Quote:

---

Originally Posted by rougeben83

That's the quote numbers from the AVO turbokit, which runs 6 psi I think.

---

yessir.

Quote:

---

Originally Posted by rougeben83

I'll be joing you soon :D

6psi only though, w/ a 14lb flywheel, using a greddy emanage ultimate. I'm not sure if the 9.5lb is too light for the NA 2.5...

https://sl-i.net/FORUM/images/import...HPIM0433-1.jpg

---

has that setup been run on a car before? that's pretty much how my old setup on my last legacy worked. The downside was that in that position I couldn't get the oil to drain from the turbo fast enough, the turbo wasn't high enough so I got constant smoking problems. The new setup has the turbo (60-1 T4) mounted in the stock wrx location and is a pretty damn tight fit.

I'm just wondering if you or whoever you got that setup from had the same issue I did with the turbo mounted that low. .... oh, and I'm guessing you don't have A/C?

Rising rate fuel controller?

Fuel Pump.
Access to a good junkyard with lots of spaire parts
And a lot of creativity.

Good luck